Victron Victron Blue Smart IP22 24/16(1) Charger 24V 16A 1 battery
The Blue Smart IP22 24/16(1) charger from Victron Energy (MPN BPC241642002) is a professional, compact 24V 16A battery charger of the latest generation with a charging output and built-in Bluetooth! The Blue Smart IP22 24/16(1) charger can be used with equipment in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and mobile homes and charges both classic 24V lead batteries and modern lithium batteries. It offers Highlights of the 24/16(1) Blue Smart IP22 Charger Intelligent charging until the battery reaches its perfect state... The seven-stage charging algorithm gets the most out of your battery. The charger delivers the energy the battery needs, keeps it in a healthy state, ensures better performance... and a longer life. Recovery of deeply discharged "dead" batteries Unlike most other brands and ranges, the Blue Smart IP22 charger will attempt to recharge a deeply discharged battery by forcing a low charge current through it. Normal charging will then resume once sufficient voltage is present between the battery terminals. View battery status remotely with the VictronConnect app The Blue Smart IP22 24/16(1) charger has built-in Bluetooth. This allows you to check the status of the charger and battery on a smartphone, tablet or laptop. All charger settings can be configured using the VictronConnect app. The main technical features of the 24/16(1) Blue Smart IP22 Charger Victron Part Number: BPC241642002 charges 24V lead-acid, gel, AGM and lithium batteries 16A maximum charging current 1 battery charging output very compact dimensions: 235 x 108 x 65mm highly modern, seven-stage loading algorithm with integrated Bluetooth for use with the free VictronConnect app Other features of the 24/16(1) Blue Smart IP22 battery charger Trend-setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat than the industry standard. Additionally, after the battery is fully charged, power consumption drops to less than 0.5 watts, which is about five to ten times better than the industry standard. Adaptive 7-stage charging algorithm The 24/16(1) Blue Smart charger is characterized by its microprocessor-controlled, “adaptive” battery management. “Adaptive” means that the charging process is automatically adapted to the type of battery use. Storage mode: Less maintenance and aging when the battery is idle Storage mode is activated whenever no discharge has occurred within 24 hours. The float charge voltage is then reduced to 2.2V/cell (13.2V for a 24V battery) to minimize gassing and prevent corrosion of the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This creates a kind of equalization charge that prevents electrolyte stratification and sulfation - the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy BPC241642002 24/16(1) IP22 Blue Smart Charger 1x User manual
€202,00
Victron Victron MultiPlus-II 48/5000/70-50 230V GX
The Multiplus-II 48/5000/70-50 GX is a high-end device combination from Victron Energy (MPN PMP482506000) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This enables the PowerControl and PowerAssist functions to be 50 A and the potential application area has been expanded to include ESS applications. The inverter module delivers a whopping 5000 W with non-linear load, or 4000 W with linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is powered by a 50 A transfer switch, which allows you to switch back and forth between the AC connections in a flash. Compared to the rest of the devices in the series, the GX variants have an integrated GX display with numerous other connection options. Key features of the Multiplus-II 48/5000/70-50 GX integrated GX control device with various communication ports PowerControl and PowerAssist –Increase grid or generator performance Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of power failures can be used in various ESS (Energy Storage System) applications ideal for professional shipping, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration Virtually unlimited power through parallel and three-phase operation can be configured locally or remotely using VEConfigure software* Technical features 5000W power at non-linear load 4000W continuous load and 9000W peak power for 48 V battery voltage, 50 A transfer switch and 70 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50 GX. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function takes the PowerControl principle to a new dimension. Peak loads often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, ie consumers are switched off, the energy that is then available again can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used in both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a power failure or an interruption in shore/generator power, the MultiPlus-II takes over the supply of the connected loads. The switchover is so fast (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when AC power is available at the MultiPlus-II input. Loads that must not discharge the battery, such as a water heater, can be connected to this output. Scope of the integrated GX device A VE.Can interface This can be used to connect Victron VE.Can devices (e.g. VE.Can MPPT ). The port can also be reconfigured for use with a compatible CAN bus Li-Ion battery via the remote console. 1xUSB port 1x Ethernet port 1x VE.Direct connection Many options for system expansion Settings can be changed in minutes using the VEConfigure software (requires a computer or laptop and MK3 USB interface). Several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (with the optional VE.Bus Smart Dongle), Battery Monitor, Digital Multi Control Panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. Operational data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. Once systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482506000 Multiplus-II 48/5000/70-50 GX 230V 1x User manual
€980,00
Victron Victron Orion-Tr 24/24-17 400W DC-DC voltage converter isolated
The Orion-Tr 24/24-17 from Victron Energy (MPN ORI242441110) is a galvanically isolated DC-DC voltage converter and ensures a regulated direct voltage and thus trouble-free operation of your DC consumers. The compact Orion-TR DC-DC voltage converter converts the DC input voltage (20-35V) into an adjustable 24V output voltage (20-30V) and delivers a constant continuous current of 17A, which corresponds to an output of 400W. Thanks to the Orion-Tr 24/24-17, you can supply every 24V consumer with exactly the right voltage. The correct voltage is guaranteed even with longer cables, as the Orion can adjust the voltage to any cable losses that occur. For many sensitive electronic devices, maintaining the exact operating voltage is essential for smooth operation. The Orion-Tr 24/24-17 can also be connected in parallel with devices of the same design and has a remote-controlled on/off switch. Key features of the Orion-Tr 24/24-17 400W (with galvanic isolation) Victron Energy Part Number: ORI242441110 for 24V battery voltage, adjustable output voltage 20-30V max. 400W output power at a maximum current of 17A wide input voltage range: 20-35V Protection class IP43, galvanic isolation 200V DC between input, output and housing can be connected in parallel with similar devices to increase performance remote-controlled on/off switch high efficiency of 87% Not designed to charge batteries. Please consider using an Orion-Tr Smart to charge the batteries. Remote controllable on/off switch The remote on/off connection eliminates the need for a high-current switch in the input wiring. The remote on/off connection can be controlled with a power-saving switch or by the motor's run/stop switch (see manual). Scope of delivery: 1x Victron Energy ORI242441110 Orion-Tr 24/24-17 17A 400W DC-DC voltage converter
€182,00
Victron Victron SmartSolar MPPT 150/100-Tr charge controller VE.Can
The Smartsolar MPPT 150/100-tr from Victron Energy (MPN SCC010100210) is part of the latest generation of smart solar controllers from the Dutch premium manufacturer. Ultra-fast power tracking and automatic power point detection in the event of partial shading are just two of the many highlights of this new class of device. The devices in classes 150/45tr to 150/100-tr are also available as a version with MC4 connections on the solar side of the charge controller instead of screw terminals. This model can also be operated in parallel with other controllers of the same type. In comparison to the BlueSolar series, the Bluetooth module in the Smartsolar family is already integrated into the controller, which makes the Smart Dongle superfluous with this device. Also new is the optionally available LCD display, which can simply be plugged onto the SmartSolar 150/85-tr when required. The display then provides all the important information about the controller. If required, the MPPT WireBox-XL Tr from Victron Energy is the ideal addition to your SmartSolar charge controller . It safely covers the cable inputs and the connection terminals of the controller, protecting them from external influences and contact. Key product features of the SmartSolar 150/100-Tr 100A 12V 24V 36V 48V MPPT Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllers with optional LCD display Built-in Bluetooth module for app-based analysis and configuration of the controller (via free Victron app on compatible devices) optional LCD display available Integrated VE.Direct data communication port for connection to additional devices such as the GX Color Control Panel or a Smart BMV battery monitor high maximum efficiency of 98% Parallel operation with other 150/100 controllers possible Adjustable constant charging voltage Adjustable trickle charge voltage Suitable for all AGM, GEL, lead-acid calcium-calcium and lithium batteries Fully programmable charging algorithms that can later be manually activated and switched via a switch on the housing Max. rated charging current 100A, 150V maximum PV open circuit voltage maximum PV power: 12V 1450W / 24V 2900W / 48V 5800W integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Remote controlled switching on and off possible via 2-pin plug Protection class IP 43 for the electronic components and protection class IP 22 for the connection area of the controller Integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming option Smart configuration and analysis via Victron Connect app Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the integrated Bluetooth module and the free Victron Connect APP. The app can then be used to configure many important functions of the SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time. Smart data communication via VE.Direct and lightning-fast Bluetooth module In case of partial shading, there may be two or more maximum power points ( MPP ) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP . However, this may not be the optimal MPP . The innovative algorithm of the SmartSolar controller will always maximize energy yield by adjusting to the optimal MPP . High-speed MPP tracker of the latest generation Especially under overcast skies, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Optional LCD display available for retrofitting If you prefer to operate and configure the Smartsolar MPPT 150/100-Tr directly, you can retrofit the Smartsolar Control SCC900600010 display. The display enables easy configuration of the controller via key input and also provides all important performance data at a glance. Comprehensive electronic protection Protection against reversed battery connection PV backflow preventer Protection against overheating of the device Protection against short circuits Protection against reversed PV connection The VE.Direct data communication port VE.Direct in text mode transmits all important parameters every second to other devices that are linked to the charge controller and thus offers the possibility of communication with additional devices Systempanel GX Color Control. The VE.Direct connection is intended for products where complete Canbus integration (VE-Direct) would be too expensive. You can find more information about VE.Direct in our Victron Energy brand shop. Scope of delivery 1x Victron SCC010100210 SmartSolar MPPT 150/100-Tr 12V 24V 36V 48V 70A charge controller User manual
€469,00
Victron Victron SmartShunt IP65 500A/50mV battery monitor
The smart SmartShunt 500A from Victron Energy is a multifunctional battery motor that allows you to view all information via your mobile phone or the VictronConnect app. This gives you easy access to all monitored battery parameters. This includes, among others, the Charge level, remaining running time, history data and much more data. It is also possible to connect the SmartShunt to a GX device, such as a Cerbo-GX or the Color Control GX, and read information from it. The connection is made via a VE.Direct cable. The Waterproof Battery Monitor is also an excellent option for BMV battery monitoring, particularly in systems where battery monitoring is required but less wiring and clutter is desired. About the SmartShunt Multifunctional battery motor Connect via Bluetooth with the VictronConnect app Connecting to a GX device Battery monitoring Waterproof according to IP65 Bolt for shunt connections: M10 The following variations are also available: 1000A 2000 A Why battery monitoring? Batteries are used in a variety of applications, mostly to store energy for future use. However, the actual amount of energy stored cannot be read directly from the battery. Factors such as undercharging or overcharging, deep discharge, excessive charging or discharging currents and high ambient temperatures can shorten the life of the battery. An advanced battery monitor enables monitoring of this and provides important feedback to you as the user. This means that appropriate measures can be taken if necessary to profitably extend the running time. The investment in the battery monitor therefore pays for itself quickly. The VictronConnect app The app is essential for setting up and monitoring! The following connection options are available: Bluetooth USB, via the optional interface Remotely controlled via a GX device and the VRM portal The app is available for the following platforms: Android Apple IOS (USB is not supported, only a connection via Bluetooth is possible) MacOS Windows (Bluetooth is not supported, only a connection via USB is possible) You can download the app from the respective app stores or from the Victron product page. Alternatively, a QR code is available. You can also find instructions for VictronConnect in the appendix. Technical data Power supply voltage range: 6.5-70V DC Current consumption: <1 mA Input voltage range, additional battery: 6.5-70V DC Battery capacity: 1-9999 Ah Operating temperature range: -40°C - +50°C Temperature measuring range: -20°C - +50°C Dimensions: 46 x 120 x 54 mm Protection class IP65 Scope of delivery: 1x Victron SmartShunt 500A/50mV battery monitor IP65
€101,00
Victron Victron BlueSolar MPPT 100/30 12V 24V 30A
The Victron MPPT 100/30 (MPN SCC020030200) belongs to the large family of BlueSolar MPPT charge controllers and, like its big siblings, it also offers ultra-fast power tracking and can therefore increase the yield of your solar system. In addition to the greater charging and PV performance, this Blue is even more different from the lower models. The 100/30 controller has the ability to fully program and save various charging algorithms. The self-created algorithms can then be selected directly using a switch wheel on the housing. The load output directly on the controller is no longer available from this model onwards. More protection compared to the smaller models of the BlurSolar MPPT series Compared to the 75/10, 75/15 and 100/15 models, the BlueSolar 100/30 Mppt has an overheating protection with a switch-off function and automatic restart after a normal operating temperature is reached. High-speed MPP tracker of the latest generation Especially under overcast conditions, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. In addition, the 100/30 has some other innovative technologies such as the VE.Direct communication port. Options for programming, real-time data and history display Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected to the Bluetooth Smart Dongles and the MPPT app or the GX Color Control via VE.Direct, for example. Please note that Bluetooth Smart Dongles and GX Color Control are separate items that are not included in the scope of delivery of the charge controller but can be purchased from us as an option. Key product features of the BlueSolar 100/30 30A 12V 24V MPPT Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Integrated VE.Direct data communication port for connection to additional devices such as Bluetooth Smart Dongle or the GX Color Control Panel high maximum efficiency of 98% Fully programmable charging algorithms that can later be activated and used manually via a switch on the housing Nominal charging current 30A, 100V maximum PV open circuit voltage 440W maximum PV power at 12V, 880W at 24V systems integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Day/night time control and light dimming option VE.Direct data communication port VE.Direct in text mode transmits all important parameters every second to other devices that are linked to the charge controller and thus offers the possibility of communication with additional devices such as the Bluetooth Smart Dongle or the GX Color Control Panel from Victron. The VE.Direct connection is intended for products where full Canbus integration (VE-Direct) would be too expensive. You can find more information about VE.Direct in our Victron brand world. Scope of delivery 1x Victron SCC020030200 BlueSolar MPPT 100/30 12V 24V 30A charge controller User manual
€101,00
Victron Victron LiFePO4 25.6/200 Smart Battery 25.6V 200Ah 5120Wh
The LiFePO4 25.6V 200Ah Smart Battery (MPN BAT524120610) from Victron Energy is a LiFePO4 battery of the latest generation. When fully charged, the LiFePO4 25.6/200 Smart stores a whopping 5120Wh of power with very low self-discharge and an outstanding service life. The LiFePO4 battery family from Victron already has an integrated cell balancing and a BMS (Battery Management System) interface. The integrated Bluetooth for connecting to the Li-Ion app rounds off the overall package. Victron LiFePO4 25.6V 200AH Smart Battery Nominal voltage: 25.6V Integrated Bluetooth for connection to the Victron Li-Ion app Victron Part Number: BAT524120610 Nominal energy at 25°C*: 5120Wh Nominal capacity at 25°C/0°C/-25°C: 200Ah / 160Ah / 100Ah Number of cycles at depth of discharge 80%/70%/50%: 2500 / 3000 / 5000 cycles Recommended continuous discharge current: <200A Maximum continuous discharge current: 400A Dimensions: 237 x 650 x 163 mm Weight: 39kg Connection terminal: M8 Further technical data can be found in the official data sheet and further down in the “technical data” section. Efficient, Economical LiFePO4 25.6V 200Ah Smart Battery Although LiFePO4 batteries are expensive compared to AGM batteries or GEL batteries, the higher purchase costs are more than worth it in most cases. With a service life of up to 5000 cycles, they exceed the maximum service life of even the best lead-acid batteries by several times. In addition, the LFP 25.6/200 scores highly in terms of space saving and weight saving, each with 70%. The energy utilization rate of 92% is also significantly higher than the 80% of lead-acid batteries, which can be of essential importance in off-grid systems, especially in off-grid solar and/or wind power plants. All-rounder: infinitely flexible with lithium technology from Victron Energy LiFePO4 Smart batteries from Victron can be implemented in almost all common applications. This technology has long played an important role in the mobile sector. But thanks to the fact that these batteries are much easier to charge than conventional lead-acid batteries and irregular charging does not harm them, they are also making their way into land applications and can now be found in almost all system classes. Parallel and series connection up to max. 3000AH at 48V Thanks to the integrated cell balancing and cell monitoring function, you can easily connect up to 10 batteries of this type in parallel and up to 4 blocks of 10 in series, which results in a maximum of 3000Ah at 48V - this corresponds to a maximum storable nominal energy of around 154,000 Wh (when used with the 300Ah 12.8V version). Integrated Bluetooth for smart handling Cell voltages, temperature and alarm status can be monitored via Bluetooth. This is very useful for detecting a (possible) problem such as a cell imbalance in good time. IMPORTANT NOTE: The use of an additional BMS is mandatory to interrupt or switch off the load when the voltage of a battery cell drops below 2.5V or to stop the charging process when the voltage of a battery cell rises above 4.2V and to switch off the system when the temperature of the cell exceeds 50°C. The VE.Bus BMS is suitable for this purpose – for further details about the devices, please refer to the respective article descriptions. Due to the classification as dangerous goods, this product will be shipped via freight forwarder! Scope of delivery: 1x Victron Energy BAT524120610 LiFePO4 25.6V 200AH Smart Battery 1x User manual
€1.923,00
Victron Victron Phoenix 12/500 VE.Direct 12V 230V 400W inverter
The SmartSolar 150/35 MPPT from Victron Energy (SCC115035210) belongs to the latest generation of smart solar charge controllers , with integrated Bluetooth for data transfer and configuration via an app on a smartphone or tablet. It supports batteries with a voltage of 12V, 24V, 36V or even 48V and is therefore very versatile. The maximum charging current is 35A and uses the latest charging methods. Depending on the system voltage, the controller can therefore use 500W (12V) to 2000W (48V) efficiently to charge your batteries. In addition, this device also compensates for partial shading and is one of the most reliable MPPT trackers on the market. The optional MPPT WireBox-M from Victron Energy is the ideal addition to your SmartSolar charge controller . It safely covers the cable inputs or connection terminals of the controller and thus protects them from external influences and contact. Key product features of the SmartSolar 150/35 35A 12V 24V 36V 48V MPPT Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllers Integrated VE.Direct data communication port for connection to additional devices such as Bluetooth Smart Dongle or the GX Color Control Panel high maximum efficiency of 98% Fully programmable charging algorithms that can later be manually activated and switched via a switch on the housing Nominal charging current 35A, 100V maximum PV open circuit voltage 12V:500W / 24V:1000W / 36V:1500W / 48V:2000W integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming option VE-Direct data port for programming, real-time data analysis and history display Modern Apple and Android smartphones and tablets can, for example, be connected to the GX Color Control system monitors, the Venus GX, or the MPPT Control Panel via VE.Direct. High-speed MPP tracker of the latest generation Especially under overcast conditions, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. In addition, the 150/35 features a number of other innovative technologies such as the VE.Direct communication port. Comprehensive electronic protection Protection against reversed battery connection PV backflow preventer Protection against overheating of the device Protection against short circuits Protection against reversed PV connection Number of charging outputs: 1 Self-consumption in standby: 10 mA Warranty: 5 years manufacturer warranty 1 Weight: 1.46 kg Manufacturer: Victron Energy Charge controller type: MPPT Product type 1: MPPT solar charge controller Protection class (IP): IP43 (electronic components) IP22 (connection area) Protection functions: battery reverse polarity, PV reverse polarity, short circuit, overheating Solar module current (max.): 35A Temperature compensation: 12V -16mV / ¡C, 24V -32mV / ¡C, 68V -32mV / ¡C Ambient temperature: -30¡C - +60¡C Scope of delivery 1x Victron Energy SCC115035210 SmartSolar MPPT 150/35 12V 24V 36V 48V 35A charge controller User manual
€141,00
Victron Victron SmartSolar MPPT 150/35 35A 12V/24V/48V solar charge controller
The SmartSolar 150/35 MPPT from Victron Energy (SCC115035210) belongs to the latest generation of smart solar charge controllers , with integrated Bluetooth for data transfer and configuration via an app on a smartphone or tablet. It supports batteries with a voltage of 12V, 24V, 36V or even 48V and is therefore very versatile. The maximum charging current is 35A and uses the latest charging methods. Depending on the system voltage, the controller can therefore use 500W (12V) to 2000W (48V) efficiently to charge your batteries. In addition, this device also compensates for partial shading and is one of the most reliable MPPT trackers on the market. The optional MPPT WireBox-M from Victron Energy is the ideal addition to your SmartSolar charge controller . It safely covers the cable inputs or connection terminals of the controller and thus protects them from external influences and contact. Key product features of the SmartSolar 150/35 35A 12V 24V 36V 48V MPPT Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllers Integrated VE.Direct data communication port for connection to additional devices such as Bluetooth Smart Dongle or the GX Color Control Panel high maximum efficiency of 98% Fully programmable charging algorithms that can later be manually activated and switched via a switch on the housing Nominal charging current 35A, 100V maximum PV open circuit voltage 12V:500W / 24V:1000W / 36V:1500W / 48V:2000W integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming option VE-Direct data port for programming, real-time data analysis and history display Modern Apple and Android smartphones and tablets can, for example, be connected to the GX Color Control system monitors, the Venus GX, or the MPPT Control Panel via VE.Direct. High-speed MPP tracker of the latest generation Especially under overcast conditions, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. In addition, the 150/35 features a number of other innovative technologies such as the VE.Direct communication port. Comprehensive electronic protection Protection against reversed battery connection PV backflow preventer Protection against overheating of the device Protection against short circuits Protection against reversed PV connection Number of charging outputs: 1 Self-consumption in standby: 10 mA Warranty: 5 years manufacturer warranty 1 Weight: 1.46 kg Manufacturer: Victron Energy Charge controller type: MPPT Product type 1: MPPT solar charge controller Protection class (IP): IP43 (electronic components) IP22 (connection area) Protection functions: battery reverse polarity, PV reverse polarity, short circuit, overheating Solar module current (max.): 35A Temperature compensation: 12V -16mV / ¡C, 24V -32mV / ¡C, 68V -32mV / ¡C Ambient temperature: -30¡C - +60¡C Scope of delivery 1x Victron Energy SCC115035210 SmartSolar MPPT 150/35 12V 24V 36V 48V 35A charge controller User manual
€167,00
Victron Victron SmartSolar MPPT 250/100-Tr charge controller VE.Can
The Smartsolar MPPT 250/100-tr from Victron Energy (MPN SCC125110210) is part of the latest generation of smart solar controllers from the Dutch premium manufacturer. Ultra-fast power tracking and automatic power point detection in the event of partial shading are just two of the many highlights of this new class of device. This model can also operate in parallel with other controllers of the same type. Compared to the Smartsolar 150/XXX series, the 250/XXX series can handle a maximum PV input voltage of 250V. This is one of the reasons why the 250 solar controller family was able to increase efficiency by a further 1 percent to a total of 99%, thereby setting new standards across the industry. This value is currently the best of all solar charge controllers we know of. Compared to the BlueSolar family, the Bluetooth module in the 250 Smartsolar series is already permanently integrated into the controller, which makes the Smart Dongle superfluous on this device if you want to analyze and configure the controller via Bluetooth using a smartphone or tablet. Also new is the optionally available LCD display, which can be easily plugged onto the SmartSolar 150/85-tr when required. The display then provides all the important information about the controller. If required, the MPPT WireBox-XL Tr from Victron Energy is the ideal addition to your SmartSolar charge controller . It safely covers the cable entries or the connection terminals of the controller and thus protects them from external influences and contact. Key product features of the SmartSolar 250/100-Tr 100A 12V 24V 36V 48V MPPT Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllers with optional LCD display Built-in Bluetooth module for app-based analysis and configuration of the controller (via free Victron app on compatible devices) optional LCD display available max. PV power: 12V 1450W / 24V 2900W / 48V 5800W Max. rated charging current 100A, 150V maximum PV open circuit voltage Max. PV input current: 250 volts Integrated VE.Direct data communication port for connection to additional devices such as the GX Color Control Panel or a Smart BMV battery monitor groundbreaking efficiency 99% Parallel operation with other 250/85 controllers possible Adjustable constant charging voltage Adjustable trickle charge voltage Suitable for all AGM, GEL, lead-acid calcium-calcium and lithium batteries Fully programmable charging algorithms that can later be manually activated and switched via a switch on the housing integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Remote controlled switching on and off possible via 2-pin plug Protection class IP 43 for the electronic components and protection class IP 22 for the connection area of the controller Integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming option Smart configuration and analysis via Victron Connect app Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the integrated Bluetooth module and the free Victron Connect APP. The app can then be used to configure many important functions of the SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time. Automatic detection of the maximum power point in case of partial shading In case of partial shading, there may be two or more maximum power points ( MPP ) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP . However, this may not be the optimal MPP . The innovative algorithm of the SmartSolar controller will always maximize energy yield by adjusting to the optimal MPP . High-speed MPP tracker of the latest generation Especially under overcast skies, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Optional LCD display available for retrofitting If you would rather operate and configure the Smartsolar MPPT 250/100-tr directly, you can retrofit the Smartsolar Control SCC900600010 display. The installation effort is limited to simply plugging the display onto the SmartSolar. The display enables easy configuration of the controller using key input, and it also provides all important performance data at a glance. Comprehensive electronic protection Protection against reversed battery connection PV backflow preventer Protection against overheating of the device Protection against short circuits Protection against reversed PV connection The VE.Direct data communication port VE.Direct in text mode transmits all important parameters every second to other devices that are linked to the charge controller and thus offers the possibility of communication with additional devices Systempanel GX Color Control. The VE.Direct connection is intended for products where complete Canbus integration (VE-Direct) would be too expensive. You can find more information about VE.Direct in our Victron Energy brand shop. Optionally available as a version with MC4 connectors The devices of classes 250/60-Tr to 250/100-Tr are also available as a version with MC4 connections on the solar side of the charge controller instead of the screw terminals. Scope of delivery 1x Victron SCC125110210 SmartSolar MPPT 250/100-tr 12V 24V 36V 48V 85A charge controller 1x User manual
€950,00 €555,90
Victron Victron SmartSolar MPPT 250/100-MC4 charge controller VE.Can
The Smartsolar MPPT 250/100-MC4 from Victron Energy (MPN SCC125110310) is part of the latest generation of smart solar controllers from the Dutch premium manufacturer. Ultra-fast power tracking and automatic power point detection in the event of partial shading are just two of the many highlights of this new device class. In addition, this model can operate in parallel with other controllers of the same type. Compared to the Smartsolar 150/XXX series, the 250/XXX series can handle a maximum PV input voltage of 250V. This is one of the reasons why the 250 solar controller family was able to increase efficiency by a further 1 percent to a total of 99%, thereby setting new standards across the industry. This value is currently the best of all solar charge controllers we know of. Compared to the BlueSolar family, the Bluetooth module in the 250 Smartsolar series is already permanently integrated into the controller, which makes the Smart Dongle superfluous on this device if you want to analyze and configure the controller via Bluetooth using a smartphone or tablet. Also new is the optionally available LCD display, which can be easily plugged onto the SmartSolar 150/85-MC4 when required. The display then provides all the important information about the controller. If required, the MPPT WireBox-XL MC4 from Victron Energy is the ideal addition to your SmartSolar charge controller . It safely covers the cable entries or the connection terminals of the controller and thus protects them from external influences and contact. Key product features of the SmartSolar 250/100-MC4 100A 12V 24V 36V 48V MPPT Ultra-fast MPPT tracker of the latest generation ensures the best possible yield even under overcast skies Automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllers with optional LCD display Built-in Bluetooth module for app-based analysis and configuration of the controller (via free Victron app on compatible devices) optional LCD display available max. PV power: 12V 1450W / 24V 2900W / 48V 5800W Max. rated charging current 100A, 150V maximum PV open circuit voltage Max. PV input current: 250 volts Integrated VE.Direct data communication port for connection to additional devices such as the GX Color Control Panel or a Smart BMV battery monitor groundbreaking efficiency 99% Parallel operation with other 250/85 controllers possible Adjustable constant charging voltage Adjustable trickle charge voltage Suitable for all AGM, GEL, lead-acid calcium-calcium and lithium batteries Fully programmable charging algorithms that can later be manually activated and switched via a switch on the housing integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Remote controlled switching on and off possible via 2-pin plug Protection class IP 43 for the electronic components and protection class IP 22 for the connection area of the controller Integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming option Smart configuration and analysis via Victron Connect app Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the integrated Bluetooth module and the free Victron Connect APP. The app can then be used to configure many important functions of the SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time. Automatic detection of the maximum power point in case of partial shading In case of partial shading, there may be two or more maximum power points ( MPP ) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP . However, this may not be the optimal MPP . The innovative algorithm of the SmartSolar controller will always maximize energy yield by adjusting to the optimal MPP . High-speed MPP -MC4acker of the latest generation Especially under overcast skies, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Optional LCD display available for retrofitting If you would rather operate and configure the Smartsolar MPPT 250/100-MC4 directly, you can retrofit the Smartsolar Control SCC900600010 display. The installation effort is limited to simply plugging the display onto the SmartSolar. The display enables the controller to be easily configured using key input, and it also provides all important performance data at a glance. Comprehensive electronic protection Protection against reversed battery connection PV backflow preventer Protection against overheating of the device Protection against short circuits Protection against reversed PV connection The VE.Direct data communication port VE.Direct in text mode transmits all important parameters every second to other devices that are linked to the charge controller and thus offers the possibility of communication with additional devices Systempanel GX Color Control. The VE.Direct connection is intended for products where complete Canbus integration (VE-Direct) would be too expensive. You can find more information about VE.Direct in our Victron Energy brand shop. Optionally available as a version with MC4 connectors The devices of classes 250/60-MC4 to 250/100-MC4 are also available as a version with MC4 connections on the solar side of the charge controller instead of the screw terminals. Scope of delivery 1x Victron SCC125110310 SmartSolar MPPT 250/100-MC4 12V 24V 36V 48V 85A charge controller 1x User manual
€975,00 €564,00
Victron Victron SmartSolar MPPT RS 450/200-MC4 48V charge controller
The MPPT RS SmartSolar from Victron Energy (MPN: SCC145120410) is a 48V solar charge controller with a PV input voltage of up to 450 VDC and an output current of 200A. It is used in on-grid and off-grid solar applications where maximum battery charging power is required. Characteristics With ultra-fast Maximum Power Point Tracking ( MPPT ) Multiple independent MPPT tracking inputs Isolated PV connectors for additional safety Wide MPPT voltage range Light, efficient and quiet Integrated display and Bluetooth communication PV insulation resistance monitoring for safety at higher voltages VE.Can and VE.Direct connection I/O connections Configure and monitor with VictronConnect app or VRM portal The integrated BluetoothSmart connection allows for quick monitoring or configuration of settings via app. The integrated 30-day history shows the individual performance of each MPPT tracker. The app allows the display of e.g. battery voltage and current, PV voltage and current, historical data and trends. The VictronConnect app is available for Android, iOS, Windows and macOS X. When the solar controller is connected to a GX device and the Internet, the Victron Remote Management Portal (VRM) provides access to the full power of your SmartSolar RS charge controllers . Additional units connected in series The SmartSolar RS charge controller is equipped with VE.Can bus ports. This allows communication with additional SmartSolar RS & VE.Can MPPT units. The additional units are simply "daisy chained" together with an RJ45 cable. When connected together, all individual charge controllers synchronize their charging levels. You can also send your data to a GX device (such as the CerboGX) for monitoring via the same cable. Technical data Battery voltage: 48V Nominal charging current: 200A Max. charging power: 11.5 kW at 57.6 V Charging algorithm: multi-stage adaptive (customizable) Max. DC PV voltage: 450V MPPT operating voltage range: 80-450V Number of trackers: 4 Max. PV operating input current: 18A per tracker Protection class: IP21 Dimensions: 487 x 434 x 146 mm Weight: 13.7 kg Scope of delivery: 1x Victron SmartSolar MPPT RS 450/200-RT 48V charge controller
€1.758,00
Victron Victron MultiPlus-II 12/3000/120-32 230V
The Multiplus-II 12/3000/120-32 is a high-end device combination from Victron Energy (MPN PMP122305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A. The inverter module delivers a whopping 3000 W with non-linear loads, or 2400 W with linear continuous loads. The 12 V battery charger is also very well proportioned with 120 A charging capacity and is complemented by a 32 A transfer switch that allows you to switch back and forth between the AC connections in a flash. Key features of the Multiplus-II 12/3000/120-32 PowerControl and PowerAssist –Increase grid or generator performance Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of power failures can be used in various applications ideal for professional shipping, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration Virtually unlimited power through parallel and three-phase operation can be configured locally or remotely using VEConfigure software* Technical features 3000 W power at non-linear load 2400 W continuous load and 5500 W peak power for 12 V battery voltage, 32 A transfer switch and 120 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 Always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the Multiplus-II 12/3000/120-32. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function gives the PowerControl principle a new dimension. Peak loads often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, ie consumers are switched off, the energy that is then available again can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used in both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a power failure or an interruption in shore/generator power, the MultiPlus-II takes over the supply of the connected loads. The switchover is so fast (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when AC power is available at the MultiPlus-II input. Loads that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion Settings can be changed in minutes using the VEConfigure software (requires a computer or laptop and MK3 USB interface). Several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (with the optional VE.Bus Smart Dongle), Battery Monitor, Digital Multi Control Panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. Operational data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. Once systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP122305010 Multiplus-II 12/3000/120-32A 1x User manual
€1.166,00
Victron Victron Blue Smart IP22 12/15(1) Charger 12V 15A 1 battery
The Blue Smart IP22 12/15(1) charger from Victron Energy (MPN BPC121542002) is a professional, compact 12V 15A battery charger of the latest generation with a charging output and built-in Bluetooth! The Blue Smart IP22 12/15(1) charger can be used with equipment in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and mobile homes and charges both classic 12V lead batteries and modern lithium batteries. It offers Highlights of the 12/15(1) Blue Smart IP22 Charger Intelligent charging until the battery reaches its perfect state... The seven-stage charging algorithm gets the most out of your battery. The charger delivers the energy the battery needs, keeps it in a healthy state, ensures better performance... and a longer life. Recovery of deeply discharged "dead" batteries Unlike most other brands and ranges, the Blue Smart IP22 charger will attempt to recharge a deeply discharged battery by forcing a low charge current through it. Normal charging will then resume once sufficient voltage is present between the battery terminals. View battery status remotely with the VictronConnect app The Blue Smart IP22 12/15(1) charger has built-in Bluetooth. This allows you to check the status of the charger and battery on a smartphone, tablet or laptop. All charger settings can be configured using the VictronConnect app. The main technical features of the 12/15(1) Blue Smart IP22 Charger Victron Part Number: BPC121542002 charges 12V lead-acid, gel, AGM and lithium batteries 15A maximum charging current 1 battery charging output very compact dimensions: 235 x 108 x 65mm highly modern, seven-stage loading algorithm with integrated Bluetooth for use with the free VictronConnect app Other features of the 12/15(1) Blue Smart IP22 battery charger Trend-setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat than the industry standard. Additionally, after the battery is fully charged, power consumption drops to less than 0.5 watts, which is about five to ten times better than the industry standard. Adaptive 7-stage charging algorithm The 12/15(1) Blue Smart charger is characterized by its microprocessor-controlled, “adaptive” battery management. “Adaptive” means that the charging process is automatically adapted to the type of battery use. Storage mode: Less maintenance and aging when the battery is idle Storage mode is activated whenever no discharge has occurred within 24 hours. The float charge voltage is then reduced to 2.2V/cell (13.2V for a 12V battery) to minimize gassing and prevent corrosion of the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This creates a kind of equalization charge that prevents electrolyte stratification and sulfation - the two main causes of premature battery failure. Scope of delivery: 1x Victron Energy BPC121542002 12/15(1) IP22 Blue Smart Charger 1x User manual
€136,55
Victron Victron SmartSolar MPPT 250/60-Tr
The Smartsolar MPPT 250/60-Tr from Victron Energy (MPN SCC125060221) belongs to the latest generation of smart solar controllers from the Dutch premium manufacturer. The controller processes a whopping 60A of solar power and can work flexibly with 12/24/36/48 V batteries and the with a maximum PV input voltage of 250V DC. Ultra-fast power tracking and automatic power point detection in the event of partial shading are just two of the many highlights of this new device class. This model can also operate in parallel with other controllers of the same type. Compared to the Smartsolar 150/XX series, the 250/XX series can handle a maximum PV input voltage of 250V. This is one of the reasons why the 250 solar controller family was able to increase efficiency by a further 1 percent to a total of 99%, thereby setting new standards across the industry. This value is currently the best of all solar charge controllers that we know of. Compared to the BlueSolar family, the Bluetooth module in the 250 Smartsolar series is already permanently integrated into the controller, which makes the Smart Dongle superfluous on this device if you want to analyze and configure the controller via Bluetooth using a smartphone or tablet. Also new is the optionally available LCD display, which can be easily plugged into the SmartSolar 250/60-tr when required. The display then provides all the important information about the controller. If required, the MPPT WireBox-L Tr from Victron Energy is the ideal addition to your SmartSolar charge controller . It safely covers the cable entries or the connection terminals of the controller and thus protects them from external influences and contact. Key product features of the SmartSolar 250/60-tr 60A 12V 24V 48V MPPT Victron Energy Part Number: SCC125060210 Max. PV power: 12 V 860 W / 24 V 1720 W / 48 V 3440 W Max. rated charging current 60A, 250V maximum PV open circuit voltage Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllers with optional LCD display Built-in Bluetooth module for app-based analysis and configuration of the controller (via free Victron app on compatible devices) optional LCD display available Integrated VE.Direct data communication port for connection to additional devices such as the GX Color Control Panel or a Smart BMV battery monitor groundbreaking efficiency 99% Parallel operation with other 250/85 controllers possible adjustable constant charging voltage adjustable trickle charge voltage suitable for all AGM, GEL, lead-acid calcium-calcium and lithium batteries Fully programmable charging algorithms that can later be manually activated and switched via a switch on the housing integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Remote controlled switching on and off possible via 2-pin plug Protection class IP 43 for the electronic components and protection class IP 22 for the connection area of the controller Integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming options Smart configuration and analysis via Victron Connect app Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the integrated Bluetooth module and the free Victron Connect APP. The app can then be used to configure many important functions of the SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time. Automatic detection of the maximum power point in case of partial shading In case of partial shading, there may be two or more maximum power points ( MPP ) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP . However, this may not be the optimal MPP . The innovative algorithm of the SmartSolar controller will always maximize energy yield by adjusting to the optimal MPP . High-speed MPP tracker of the latest generation Especially under overcast conditions, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Optional LCD display available for retrofitting If you prefer to operate and configure the Smartsolar MPPT 250/60-tr directly, you can retrofit the Smartsolar Control SCC900600010 display. The display enables easy configuration of the controller via key input and also provides all important performance data at a glance. Comprehensive electronic protection Protection against reversed battery connection PV backflow preventer Protection against overheating of the device Protection against short circuits Protection against reversed PV connection The VE.Direct data communication port VE.Direct in text mode transmits all important parameters every second to other devices that are linked to the charge controller , thus offering the possibility of communication with additional devices such as the GX Color Control system panel. The VE.Direct connection is intended for products where full Canbus integration (VE-Direct) would be too expensive. You can find more information about VE.Direct in our Victron Energy brand shop. Optionally available as a version with MC4 connectors The 250/60-tr is also available as a version with MC4 connectors on the solar side of the charge controller instead of the screw terminals and you can find this here. Scope of delivery 1x Victron SCC125060210 SmartSolar MPPT 250/60-Tr 12V 24V 48V 60A charge controller 1x User manual
€376,00
Victron Victron BlueSolar MPPT 75/10 12V 24V 10A
The Victron MPPT 75/10 (MPN SCC010010050R) belongs to the large family of BlueSolar MPPT charge controllers and, like its big siblings, it also offers ultra-fast power tracking and can therefore increase the yield of your solar system. MPP tracker of the latest generation Especially under overcast conditions, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. The 75/10 also features a number of other innovative technologies. Options for programming, real-time data and history display Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected to the Bluetooth Smart Dongles and the MPPT app or the GX Color Control via VE.Direct, for example. Please note that Bluetooth Smart Dongles and GX Color Control are separate items that are not included in the scope of delivery of the charge controller but can be purchased from us as an option. Key product features of the BlueSolar 75/10 10A 12V 24V MPPT Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Integrated VE.Direct data communication port for connection to additional devices such as Bluetooth Smart Dongle or the GX Color Control Panel 12V 24V systems possible Nominal charging current 10A 145W maximum PV power at 12V, 290W at 24V systems Load output with 10A power and automatic load shutdown in case of impending battery undervoltage (deep discharge protection integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm programmable battery charging algorithm integrated Battery Life algorithm extends the life of your batteries if it is active and all loads run via the load output on the controller Day/night time control and light dimming option VE.Direct data communication port integrated VE.Direct in text mode transmits all important parameters every second to other devices that are linked to the charge controller and thus offers the possibility of communication with additional devices such as the Bluetooth Smart Dongle or the GX Color Control Panel from Victron. The VE.Direct connection is intended for products where full CANbus integration (VE-Direct) would be too expensive. You can find more information about VE.Direct in our Victron brand world in the information area. Battery Life algorithm helps increase battery life If the solar charge controller is not able to charge the battery to its full capacity within a day, the status of the battery will constantly switch between "partially charged" and "end of discharge". This operating mode (no regular full charging) is optimal for small lead batteries, but in the case of lead-acid batteries in particular, such irregular charging and discharging leads to damage to the battery after just a few months and the service life is sometimes shortened quite significantly. The Battery Life algorithm monitors the battery's state of charge and, if necessary, increases the load disconnection threshold day by day (i.e. the load is disconnected earlier) until the energy harvested is sufficient to charge the battery to nearly 100%. From this point, the load disconnection threshold is modulated so that the charge is near 100% approximately once a week. Scope of delivery 1x Victron SCC010010050R BlueSolar MPPT 75/10 12V 24V 10A charge controller
€46,89
Victron Victron GX Touch 70 display panel for Cerbo GX
The GX Touch 70 display from Victron Energy (MPN BPP900455070) is the display accessory for the Cerbo GX communication center. The 7-inch touchscreen display provides an instant overview of your system and allows you to make settings in no time. The display is easily connected to Cerbo GX via a cable. Its super slim, waterproof design and easy installation offer a lot of flexibility. Features of the GX Touch 70 7-inch touchscreen display Instant system overview Easy installation from above Connection via a cable The addition to the Cerbo GX The GX Touch 70 display is the ideal addition to get the most out of your Cerbo GX communication center. Access it directly from the GX Touch 70 using Bluetooth capability and optimize your system and make changes quickly and easily. Scope of delivery: 1x GX Touch 70 display 1x HDMI-USB connection cable 1x mounting material
€294,00
Victron Victron SmartSolar MPPT 150/45
The Smartsolar MPPT 150/45 from Victron Energy (MPN SCC115045212) belongs to the latest generation of smart solar controllers from the Dutch premium manufacturer and processes a whopping 45A of solar power and can work flexibly with 12/24/36/48 V batteries. Ultra-fast power tracking and automatic power point detection in the event of partial shading are just two of the many highlights of this new device class. The SmartSolar 150/45 is also available as a version with MC4 connections on the solar side of the charge controller instead of screw terminals. This model can also be operated in parallel with other controllers of the same type. In comparison to the BlueSolar series, the Bluetooth module in the Smartsolar family is already integrated into the controller, which makes the Smart Dongle superfluous for this device. The MPPT WireBox-L Tr from Victron Energy is the ideal addition to your SmartSolar charge controller . It safely covers the cable inputs and the connection terminals of the controller, protecting them from external influences and contact. Key product features of the SmartSolar 150/45 45A 12V 24V 36V 48V MPPT Ultra-fast MPP tracker of the latest generation ensures the best possible yield even under overcast skies Nominal charging current 45A, 150V maximum PV open circuit voltage maximum PV power: 12 V 650 W / 24 V 1300 W / 48 V 2600 W Victron Energy Part Number (MPN): SCC115045212 Automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllers Built-in Bluetooth module for app-based analysis and configuration of the controller (via free Victron app on compatible devices) Integrated VE.Direct data communication port for connection to additional devices such as the GX Color Control Panel or a Smart BMV battery monitor high maximum efficiency of 98% Parallel operation with other 150/45 controllers possible adjustable constant charging voltage adjustable trickle charge voltage suitable for all AGM, GEL, lead-acid calcium-calcium and lithium batteries Fully programmable charging algorithms that can later be activated and switched manually via a switch on the housing integrated protection against battery polarity reversal multi-stage and adaptive charging algorithm Remote controlled switching on and off possible via 2-pin plug Protection class IP 43 for the electronic components and protection class IP 22 for the connection area of the controller Integrated temperature sensor balances maintenance and constant charge voltage according to temperature Day/night time control and light dimming option Smart data communication via VE.Direct and lightning-fast Bluetooth Modern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the integrated Bluetooth module and the free Victron Connect APP. The app can then be used to configure many important functions of the MPPT 150/45 SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time. Automatic detection of the maximum power point in case of partial shading In case of partial shading, there may be two or more maximum power points ( MPP ) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP . However, this may not be the optimal MPP . The innovative algorithm of the SmartSolar 150/45 will always maximize the energy yield by adjusting to the optimal MPP . High-speed MPP tracker of the latest generation Especially under overcast skies, when the light intensity is constantly changing, an extremely fast MPPT controller improves energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. comprehensive electronic protection Protection against reversed battery connection PV backflow preventer Protection against overheating of the device Protection against short circuits Protection against reversed PV connection the VE.Direct data communication port VE.Direct in text mode transmits all important parameters every second to other devices that are linked to the charge controller and thus offers the possibility of communication with additional devices Systempanel GX Color Control. The VE.Direct connection is intended for products where full Canbus integration (VE-Direct) would be too expensive. You can find more information about VE.Direct in our Victron Energy brand shop. Scope of delivery 1x Victron SCC115045212 SmartSolar MPPT 150/45 12V 24V 36V 48V 45A charge controller User manual
€198,00
Victron Victron MultiPlus-II 48/3000/35-32 230V
The Multiplus-II 48/3000/35-32 is a high-end device combination from Victron Energy (MPN PMP482305010) that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and expands the potential area of application to ESS applications. The inverter module delivers a whopping 3000 W with non-linear load, or 2400 W with linear continuous load. The 48 V battery charger is also very well proportioned with 35 A charging power and is complemented by a 32 A transfer switch that can be used to switch back and forth between the AC connections in a flash. Key features of the Multiplus-II 48/3000/35-32 PowerControl and PowerAssist –Increase grid or generator performance Built-in anti-islanding function and connection option for external current sensor (optional) can be used as a backup device in grid-connected systems for power supply in case of power failures can be used in various ESS (Energy Storage System) applications ideal for professional shipping, yachts, vehicles and land-based, off-grid applications VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration Virtually unlimited power through parallel and three-phase operation can be configured locally or remotely using VEConfigure software* Technical features 3000W power at non-linear load 2400W continuous load and 6000W peak power for 48 V battery voltage, 32 A transfer switch and 35 A battery charger Output voltage: 230 VAC, frequency: 50 Hz Max. efficiency is 95%, protection class IP22 always enough power thanks to PowerControl and PowerAssist A maximum mains or generator current can be set on the Multiplus-II 48/3000/35-32. The MultiPlus-II then takes into account other connected AC consumers and only uses the current that is "left over" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function takes the PowerControl principle to a new dimension. Peak loads often only occur for a limited period of time. In such a case, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, ie consumers are switched off, the energy that is then available again can be used to charge the batteries. Solar power: alternating current even in the event of a power failure The device can be used in both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters. Maximum flexibility thanks to two AC outputs The main output ensures uninterrupted operation. In the event of a power failure or an interruption in shore/generator power, the MultiPlus-II takes over the supply of the connected loads. The switchover is so fast (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power when AC power is available at the input of the MultiPlus-II. Loads that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansion Settings can be changed in minutes using the VEConfigure software (requires a computer or laptop and MK3 USB interface). Several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (with the optional VE.Bus Smart Dongle), Battery Monitor, Digital Multi Control Panel. Remote configuration and monitoring Install a Color Control GX or other GX products to connect to the Internet. Operational data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. Once systems are connected to the Internet, they can be accessed remotely and settings can be changed. Scope of delivery: 1x Victron PMP482305010 Multiplus-II 48/3000/35-32A 1x User manual
€624,00
Victron Victron Energy Meter EM24 - 3 phase - max 65A/phase Ethernet
The Energy Meter EM24 from Victron Energy (MPN REL200200100) is a three-phase energy meter with a maximum of 65A per phase. It is used in the house connection/meter box to measure the power on all three phases. The energy meter can be used as: Network meter and is used as a control input for an ESS system Measuring device for the performance of a PV inverter Measuring device for the power of an alternator For all of the above uses, the meter should be connected to the local network so that the GX device can reach it. Note on GX firmware versions To support Ethernet EM24 meters, Venus 2.60 is the minimum firmware required on the GX device. Scope of delivery: 1x Victron Energy Meter EM24 REL200200100
€164,00
Victron Victron Cerbo-S GX system monitoring
The Cerbo-S GX communication center from Victron Energy (MPN BPP900450120) enables perfect control over your system and maximizes its performance. Maximizing system performance has never been easier. The more cost-effective variant of the Cerbo-GX series still has all the important features for flawless communication, except for the BMS-Can connection, temperature sensor inputs and resistive tank level inputs. Easy monitoring and control With the Cerbo-S GX you can quickly monitor power consumption, energy production from PV, generator and grid from anywhere. Easily control the current limit for shore power feed-in, the (automatic) start/stop generator or change any settings to optimize the system. Track alerts, perform diagnostic checks and solve problems remotely. Features of the Cerbo-S GX communication center Easy control of your system Flexible connection options Maximize your system performance Uncomplicated assembly Technical data Operating voltage: 8-70 V/DC Mounting: Wall or DIN rail 35mm Dimensions: 78 x 154 x 48 mm Operating temperature range: -20 to +50°C Cable length: 2 meters Safety: IEC 62368-1 EMC EN: EN 301489-1, EN 301489-17 Available connections 3 VE.Direct ports 3 USB ports 4 digital inputs 2 relays 2 VE.BUS 2 VE.CAN Flexible connection options The system can be controlled using the Cerbo GX communication center regardless of time and place. The device offers three different connection options: either via the free Victron Remote Management (VRM) portal, the Victron Energy GX Touch 50 (5-inch touchscreen display) or via the VictronConnect app via Bluetooth. Scope of delivery: 1x Cerbo-S GX 1x power cable with inline fuse and M8 connection eyes for battery or DC busbar mounting. 2x VE.Can termination resistors 1x terminal blocks for all connections on each side.
€197,00
Victron Victron Orion-Tr Smart non-isolated DC-DC converter charger 24/24-17A (400W)
The Orion Tr-Smart DC-DC from Victron Energy (MPN ORI242440140) is a professional, DC to DC adaptive 3-stage charger with integrated Bluetooth, known in the market as a battery-to-battery (B2B) charger. The charging booster is suitable for use in dual battery systems in vehicles or on boats, where the alternator and starter battery are used to charge the service battery. The charger can be used in 12V or 24V systems and is suitable for both lead and lithium batteries. Models up to 400W are available and an unlimited number of devices can be connected in parallel to increase the output power. Key features Suitable for Bluetooth Smart Fully programmable Adaptive 3-stage charging algorithm Remote on/off Short-circuit proof Parallel connection possible to increase the output current Overtemperature protection Protection class IP43 Suitable for Bluetooth Smart Monitoring, changing settings and updating the charger with new software features can be done using any Bluetooth-enabled smartphone, tablet or other device. Adaptive 3-stage charging algorithm: constant current – constant voltage – maintenance For lead batteries, it is important that the absorption time is kept short during shallow discharges to avoid overcharging the battery. After a deep discharge, the constant voltage time is automatically extended to ensure that the battery is fully charged. For lithium batteries, the recording time is fixed, default is 2 hours. Alternatively, a fixed output voltage can be selected. Remote on/off A remote-controlled on/off switch or a relay contact can be connected to the two-pin plug. Alternatively, connection H (right) of the two-pin plug can be connected to a positive battery terminal or connection L (left) of the two-pin plug can be connected to the negative battery terminal (or, for example, to the body of a vehicle). Technical data Input voltage range: 20-35 V Nominal output voltage: 24.2 V Output voltage adjustment range: 20-30 V Output voltage tolerance: ±0.2 V Cont. output current at nominal output voltage and 40°: 17 A Cont. output power at 40°C: 400 W Operating temperature range: -20°C - +55°C Weight: 1.6kg Dimensions: 130 x 186 x 70 mm Scope of delivery: 1x Victron Energy Orion-Tr Smart DC/DC charging booster 24/24-17A (400W) ORI242440140
€232,00
Victron Victron GX Touch 50 display panel for Cerbo GX
The GX Touch 50 display from Victron Energy (MPN BPP900455050) is the display accessory for the Cerbo GX communication center. The 5-inch touchscreen display provides an instant overview of your system and allows you to make settings in no time. The display is easily connected to Cerbo GX via a cable. Its super slim, waterproof design and easy installation offer a lot of flexibility. Features of the GX Touch 50 5-inch touchscreen display Instant system overview Easy installation from above Connection via a cable The addition to the Cerbo GX The GX Touch 50 display is the ideal addition to get the most out of your Cerbo GX communication center. Access it directly from the GX Touch 50 using Bluetooth capability and optimize your system and make changes quickly and easily. Scope of delivery: 1x GX Touch 50 display 1x HDMI-USB connection cable 1x mounting material
€199,00
Victron Victron Orion-XS 12/12-50A 700W DC-DC battery charger
The Orion-XS 12/12-50 700W battery charger from Victron Energy (MPN ORI121217040) offers comprehensive remote monitoring and control capabilities, giving you complete control over your device and system. The Orion-XS revolutionizes adaptive DC-DC battery charging. It is specifically designed for use in dual battery systems charged by a (smart) alternator. The innovative technology for cooling the aluminum board ensures an astonishing 98% efficiency without the need for fans. The Orion-XS acts as both a DC-DC battery charger and a power source, offering a wide input and output voltage range. This is especially important on vehicles with a Euro 5 or Euro 6 smart alternator, which often delivers too low a charging voltage even when the engine is running, or in situations with longer cables, as is common on boats and motorhomes, voltage drops can occur. In such scenarios, precise and controlled charging is essential to fully charge the service battery and protect the starter/input battery from discharging. Key features of the Orion-XS 12/12-50 700W fully configurable Engine shutdown detection Low temperature shutdown efficient cooling works with VictronConnect optional remote monitoring IP65 protection class (dust and waterproof) adaptive four-stage charging algorithm With lead acid batteries, it is crucial to keep the constant voltage phase short during shallow discharges to prevent overcharging the battery. After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged. The Orion XS offers fully programmable charging algorithms as well as eight pre-programmed battery settings. remote controlled on/off switch The Orion XS can be switched on and off via the remote on/off connector or via the VictronConnect app. Typical applications are wiring a switch or a battery management system (BMS). intelligent alternator compatibility A built-in mechanism detects whether the engine is running (engine shutdown detection), which only activates the charger when the alternator is supplying power. This ensures that the charger only draws power when the alternator is supplying power, i.e. when the engine is running. comprehensive electronic protection Protection features include overload, short circuit and over temperature. The charger is protected against overheating by reducing the output power when the maximum device temperature is reached. Parallel connection to increase the output current It is possible to connect any number of devices in parallel. Technical data Max. constant short circuit current: 50A Continuous output power up to 40°C: 700W Input voltage range: 9-17V adjustable output voltage range: 10-17V Output voltage tolerance: +/- 0.25% Max. efficiency: 98.5% Power consumption without load: <100mA Power consumption in standby mode: <1.5mA Temperature range: -20°C to +60°C Humidity: max. 95% non-condensing Weight: 0.330kg Dimensions: 137.3mm x 123.1 x 40mm Scope of delivery 1x Victron Energy Orion-XS 12/12 50 700W DC-DC battery charger
€354,00
You have seen 240 out of 319 products