Wall boxes
-
Schneider Electric Schneider Electric Evink Pro AC, 7.4KW, 32A, 1P+N, T2S socket, mid meters
This evil Pro AC product is a wall-mounted charging station for all electrical vehicles in accordance with standard IEC 61851-1. Installation on the floor is also possible, either attached to a stand or integrated into a housing set. The stand and housing set must be ordered separately. Installation possible inside and outside. The IP protection class is IP55. The IK protection type is IK10. The operating temperature is between -30 ° C and 45 ° C. The storage temperature is between -40 ° C and 80 ° C. The output type is a T2 socket with flap (T2S), which is attached to the front of the station. All contacts of the T2S socket are silvered to avoid overheating. The nominal output power is 7.4 kW. Provision in phase (1p+n). The nominal charging current is 32 A at 220 V to 240 VAC at a frequency of 50 Hz to 60 Hz. IT compatible with an additional separator in the power supply. The charging station is easy to install and put into operation. Recommended for apartment buildings, vehicle fleets, street or workplace. The dimensions are (b) 317 mm x (h) 529 mm x (t) 153 mm. The product weight is 7.2 kg. The color is dark gray (RAL 7016). Included are a built-in protection against error-equal power current with 6 MA error equal strom detection (RDC-DD) and a 30 MA fault electricity protection device (RCD) of type A-SI. For safety reasons, an MNX undervoltage trigger is also integrated into the charging station. In addition, the EV ready requirements must be met. In addition, a mid-energy counter with accuracy class 1 is integrated into the charging station. The charging station can be fed by a cable that runs from behind, top or bottom. To charge electric vehicles, access control is carried out by user authentication using RFID or NFC ID. The charging station can also be used freely. The charging process can be started in a time delay. During the loading time, the performance can be limited to ensure service contact and optimize the loading time of all charging stations based on the same feed. Two Ethernet RJ45 inputs for LAN connection. The parameters are defined with the Esetup app via Bluetooth or Ecostruxure EV Charging Expert. The charging station can be managed in standalone or clustered architecture. The OCPP 1.6 Communication protocol is used to connect to the surveillance device. The available services are CDR, diagnostic options and charging management. The charging station has CE and EV Ready certification.
€1.783,00
-
Schneider Electric Schneider Electric Evink Pro AC, 22KW, 32A, 3P+N, T2S socket
This evil Pro AC product is a wall-mounted charging station for all electric vehicles that corresponds to the IEC61851-1 standard. It can also be ground, either attached to a base or integrated into a kit housing. The base and kit housing must be ordered separately. It can be installed both indoors and outdoors. The IP protective degree is IP55. The IK protective degree is IK10. The operating temperature is between -30 ° C and 50 ° C. The storage temperature is between -40 ° C and 80 ° C. The output type is a T2 socket with closure (T2S), which is attached to the front of the station. All contacts of the T2S socket are silver-plated to avoid overheating. The nominal output power is 22 kW. It is delivered three -phase (3P+N). The nominal charging current is 32 A at 380 V to 415 VAC with a frequency of 50 Hz to 60 Hz. It can be used with a TT, TN-S or TN-C-S earth-inheritance system. It is also IT compatible with an additional separator on the power supply. The charging station is easy to install and put into operation. It is recommended at home and in fleet, on the street or at work. The dimensions are (b) 317 mm x (h) 529 mm x (t) 153 mm. The product weight is 7.2 kg. Its color is white (RAL9003). It has a built-in protection against error equivalent current with a 6-MA error-like current detection detection device (RDC-DD). For safety reasons, an MNX under-voltage resolution is also integrated in the charging station. In addition, it is necessary to meet the EV ready requirements. The charging station can be supplied via a cable that comes from behind, at the top or below. In order to charge an electric vehicle, access control is carried out via user authentication via RFID or NFC ID. The charging station can also be used for free access. The charging start can be delayed in a time delay. During the loading time, the performance can be limited to ensure operating continuity and optimize the loading time of all charging stations based on the same feed. It has 2 Ethernet RJ45 ports for the LAN connection. The parameters are set up via the Esetup app via Bluetooth or Ecostruxure EV Charging Expert. The charging station can be managed in an independent or in a cluster architecture. The communication protocol OCCP 1.6 is used to connect to the surveillance device. The available services are the charging line recordings, the diagnostic functions and load management. The charging station is CE and EV ready-certified. The firmware from Evink Pro AC is waited up to 2 years after the end of the marketing.
€1.579,00
-
Schneider Electric Schneider Electric Evink Pro AC, 22KW, 32A, 3P+N, T2S Socket, Type B
This evil Pro AC product is a wall-mounted charging station for all electric vehicles that corresponds to the IEC61851-1 standard. It can also be ground, either attached to a base or integrated into a kit housing. The base and kit housing must be ordered separately. It can be installed both indoors and outdoors. The IP protective degree is IP55. The IK protective degree is IK10. The operating temperature is between -30 ° C and 50 ° C. The storage temperature is between -40 ° C and 80 ° C. The output type is a T2 socket with closure (T2S), which is attached to the front of the station. All contacts of the T2S socket are silver-plated to avoid overheating. The nominal output power is 22 kW. It is delivered three -phase (3P+N). The nominal charging current is 32 A at 380 V to 415 VAC with a frequency of 50 Hz to 60 Hz. It can be used with a TT, TN-S or TN-C-S earth-inheritance system. It is also IT compatible with an additional separator on the power supply. The charging station is easy to install and put into operation. It is recommended at home and in fleet, on the street or at work. The dimensions are (b) 317 mm x (h) 529 mm x (t) 153 mm. The product weight is 7.2 kg. Its color is white (RAL9003). It has built-in protection against error equal power with an residual current circuit breaker (RCD) of the type B-EP (electric vehicle). For safety reasons, an MNX undervoltage trigger is also integrated in the charging station. In addition, it is necessary to meet the EV ready requirements. The charging station can be supplied via a cable that comes from behind, at the top or below. In order to charge an electric vehicle, access control is carried out via user authentication via RFID or NFC ID. The charging station can also be used for free access. The charging start can be delayed in a time delay. During the loading time, the performance can be limited to ensure operating continuity and optimize the loading time of all charging stations based on the same feed. It has 2 Ethernet RJ45 ports for the LAN connection. The parameters are set up via the Esetup app via Bluetooth or Ecostruxure EV Charging Expert. The charging station can be managed in an independent or in a cluster architecture. The communication protocol OCCP 1.6 is used to connect to the surveillance device. The available services are the charging line recordings, the diagnostic functions and load management. The charging station is CE and EV ready-certified. The firmware from Evink Pro AC is waited up to 2 years after the end of the marketing.
€1.818,00
-
Schneider Electric Schneider Electric Evink Pro AC, 22KW, 32A, 3P+N, T2S Socket, Type A
This evil Pro AC product is a wall-mounted charging station for all electric vehicles that corresponds to the IEC61851-1 standard. It can also be ground, either attached to a base or integrated into a kit housing. The base and kit housing must be ordered separately. It can be installed both indoors and outdoors. The IP protective degree is IP55. The IK protective degree is IK10. The operating temperature is between -30 ° C and 50 ° C. The storage temperature is between -40 ° C and 80 ° C. The output type is a T2 socket with closure (T2S), which is attached to the front of the station. All contacts of the T2S socket are silver-plated to avoid overheating. The nominal output power is 22 kW. It is delivered three -phase (3P+N). The nominal charging current is 32 A at 380 V to 415 VAC with a frequency of 50 Hz to 60 Hz. It can be used with a TT, TN-S or TN-C-S earth-inheritance system. It is also IT compatible with an additional separator on the power supply. The charging station is easy to install and put into operation. It is recommended at home and for fleet, on the street or at work. The dimensions are (b) 317 mm x (h) 529 mm x (t) 153 mm. The product weight is 7.2 kg. Its color is white (RAL9003). It has built-in protection against error equal current with a 6-MA error-like current detection device (RDC-DD) and a 30-mA error current control switch (RCD) of the AT A-SI. For safety reasons, an MNX undervoltage trigger is also integrated into the charging station. In addition, it is necessary to meet the EV-Ready requirements. The charging station can be supplied via a cable that comes from behind, at the top or below. In order to charge an electric vehicle, access control is carried out by user authentication via RFID or NFC ID. The charging station can also be used for free access. The charging start can be delayed in a time delay. During the loading time, the performance can be limited to ensure operating continuity and optimize the loading time of all charging stations based on the same feed. It has 2 Ethernet RJ45 ports for the LAN connection. The parameters are set up via the Esetup app via Bluetooth or Ecostruxure EV Charging Expert. The charging station can be managed in a standalone or cluster architecture. The communication protocol OCCP 1.6 is used to connect to the surveillance device. The available services are the charging line recordings, the diagnostic functions and load management. The charging station is CE and EV ready-certified. The firmware from Evink Pro AC is waited up to 2 years after the end of the marketing.
€1.795,00
-
Schneider Electric Schneider Electric Evink Pro AC, 22KW, 32A, 3P+N, T2 Socket, mid meters
This evil Pro AC product is a wall-mounted charging station for all electric vehicles that corresponds to the IEC61851-1 standard. It can also be ground, either attached to a base or integrated into a kit housing. The base and kit housing must be ordered separately. It can be installed both indoors and outdoors. The IP protective degree is IP55. The IK protective degree is IK10. The operating temperature is between -30 ° C and 50 ° C. The storage temperature is between -40 ° C and 80 ° C. The output type is a T2 socket with closure (T2S), which is attached to the front of the station. All contacts of the T2S socket are silver-plated to avoid overheating. The nominal output power is 22 kW. It is delivered three -phase (3P+N). The nominal charging current is 32 A at 380 V to 415 VAC with a frequency of 50 Hz to 60 Hz. It can be used with a TT, TN-S or TN-C-S earth-inheritance system. It is also IT compatible with an additional separator on the power supply. The charging station is easy to install and put into operation. It is recommended at home and in fleet, on the street or at work. The dimensions are (b) 317 mm x (h) 529 mm x (t) 153 mm. The product weight is 7.2 kg. Its color is white (RAL9003). It has a built-in protection against error equivalent current with a 6-MA error-like current detection detection device (RDC-DD). In addition, it is necessary to meet the EV-Ready requirements. A mid-energy counter with an accuracy class of class 1 is also integrated into the charging station. The charging station can be supplied via a cable that comes from behind, at the top or below. In order to charge an electric vehicle, access control is carried out via user authentication via RFID or NFC ID. The charging station can also be used for free access. The charging start can be delayed in a time delay. During the loading time, the performance can be limited to ensure operating continuity and optimize the loading time of all charging stations based on the same feed. It has 2 Ethernet RJ45 ports for the LAN connection. The parameters are set up via the Esetup app via Bluetooth or Ecostruxure EV Charging Expert. The charging station can be managed in an independent or in a cluster architecture. The communication protocol OCCP 1.6 is used to connect to the surveillance device. The available services are the charging line recordings, the diagnostic functions and load management. The charging station is CE and EV ready-certified. The firmware from Evink Pro AC is waited up to 2 years after the end of the marketing.
€2.100,00
-
Schneider Electric Schneider Electric Evink Pro AC, 11KW, 16A, 3P+N, T2S socket
This evil Pro AC product is a wall-mounted charging station for all electrical vehicles in accordance with standard IEC 61851-1. Installation on the floor is also possible, either attached to a stand or integrated into a housing set. The stand and housing set must be ordered separately. Installation possible inside and outside. The IP protection class is IP55. The IK protection type is IK10. The operating temperature is between -30 ° C and 45 ° C. The storage temperature is between -40 ° C and 80 ° C. The output type is a T2 socket with flap (T2S), which is attached to the front of the station. All contacts of the T2S socket are silvered to avoid overheating. The nominal output power is 7.4 kW. Provision in phase (1p+n). The nominal charging current is 32 A at 220 V to 240 VAC at a frequency of 50 Hz to 60 Hz. IT compatible with an additional separator in the power supply. The charging station is easy to install and put into operation. Recommended for apartment buildings, vehicle fleets, street or workplace. The dimensions are (b) 317 mm x (h) 529 mm x (t) 153 mm. The product weight is 7.2 kg. The color is dark gray (RAL 7016). Included are a built-in protection against error-equal power current with 6 MA error equal strom detection (RDC-DD) and a 30 MA fault electricity protection device (RCD) of type A-SI. For safety reasons, an MNX undervoltage trigger is also integrated into the charging station. In addition, the EV ready requirements must be met. In addition, a mid-energy counter with accuracy class 1 is integrated into the charging station. The charging station can be fed by a cable that runs from behind, top or bottom. To charge electric vehicles, access control is carried out by user authentication using RFID or NFC ID. The charging station can also be used freely. The charging process can be started in a time delay. During the loading time, the performance can be limited to ensure service contact and optimize the loading time of all charging stations based on the same feed. Two Ethernet RJ45 inputs for LAN connection. The parameters are defined with the Esetup app via Bluetooth or Ecostruxure EV Charging Expert. The charging station can be managed in standalone or clustered architecture. The OCPP 1.6 Communication protocol is used to connect to the surveillance device. The available services are CDR, diagnostic options and charging management. The charging station has CE and EV Ready certification.
€1.670,00
-
Schneider Electric Schneider Electric Evink Pro AC, 11KW, 16A, 3P+N, T2 cable
This evil Pro AC product is a wall-mounted charging station for all electrical vehicles. The charging station corresponds to the IEC 61851-1 standard. It can be attached to a stand on the floor or integrated into a housing set. The stand and housing set must be ordered separately. Installation possible inside and outside. The IP protection class is IP55. The IK protection type is IK10. The operating temperature is between -30 ° C and 50 ° C. The storage temperature is between -40 ° C and 80 ° C. The output type is a connected 5 meter cable with a T2 connector with flap (T2S) at the end, installed at the top of the charging station. All contacts of the T2 connector are silvered to avoid overheating. The nominal output power is 11 kW. Provision three -phase (3P+N). The nominal charging current is 16 A at 380 V to 415 VAC at a frequency of 50 Hz to 60 Hz. Using with TT, TN-S or TN-C-S-sterming system possible. Also IT compatible with an additional separator in the power supply. The charging station is easy to install and put into operation. Recommended for use at home, in vehicle fleets, on the street or at the workplace. The dimensions are (b) 317 mm x (h) 529 mm x (t) 183 mm. The product weighs 10 kg. The color is white (RAL 9003). Included are a built-in creep electricity protection with 6 MA creeping stream detection (RDC-DD) and a 30 MA fault electricity protection device (RCD) of type A-SI. For safety reasons, an MNX subsequent trigger is also integrated into the charging station. In addition, the EV ready requirements must be met. The charging station can be fed by a cable that runs from behind, top or bottom. To charge electric vehicles, access control is carried out by user authentication via an RFID or NFC ID. The charging station can also be used freely. The start of the charging process can be delayed. During the loading time, the performance can be limited to ensure service contact and optimize the loading time of all charging stations based on the same power supply. Two Ethernet RJ45 inputs for LAN connection. The parameters are defined with the Esetup app via Bluetooth or Ecostruxure EV Charging Expert. The charging station can be managed in standalone or clustered architecture. The communication protocol OCCP 1.6 is used to connect to the surveillance device. Available services are charging data, diagnostics and charging management. The charging station has CE and EV Ready certification.
€1.837,00
-
Schneider Electric Schneider Electric Evink Home, 7.4kW, 32A, 1P+N, with a fixed 5m charging cable, with RDC-DD
Evink Home is a simple and easy-to-install charging station, which ensures the correct load of your e-vehicle in order to minimize top loads and to avoid power crossing and associated penalties.
€920,00
-
Schneider Electric Schneider Electric Evink Home, 7.4KW, 32A, 1P+N, 1xt2, with RDC-DD
Evink Home is a simple and easy-to-install charging station, which ensures the correct load of your e-vehicle in order to minimize top loads and to avoid power crossing and associated penalties.
€820,00
-
Schneider Electric Schneider Electric Evink Home, 3.7kW, 16A, 1P+N, with a fixed 5m charging cable, with RDC-DD
Evink Home is a simple and easy-to-install charging station, which ensures the correct load of your e-vehicle in order to minimize top loads and to avoid power crossing and associated penalties.
€907,00
-
Schneider Electric Schneider Electric Evink Home, 3.7kW, 16A, 1P+N, 1xt2, with RDC-DD
Evink Home is a simple and easy-to-install charging station, which ensures the correct load of your e-vehicle in order to minimize top loads and to avoid power crossing and associated penalties.
€796,00
-
Schneider Electric Schneider Electric Evink Home, 11kW, 16A, 3P+N, 1xt2, with RDC-DD
Evink Home is a simple and easy-to-install charging station, which ensures the correct load of your e-vehicle in order to minimize top loads and to avoid power crossing and associated penalties.
€814,00
-
Kostal Kostal EV Wallbox Enector AC 3.7/11
In the design, the Wallbox Enector follows its function simply and elegantly. The compact design enables space -saving installation. The robust housing allows safe use indoors and outdoors. An LED display on the housing front provides information quickly and clearly about all important status messages and shows the charging operation. The equipment of the Kostal Wallbox is also impressive: the 7.5 meter long charging cable included in the scope of delivery leaves enough scope to refuel the electric vehicle within a convenient range. The type 2 charging plug for the vehicle connection is tailored to the charging point in common fashion 3. The enector does 3.7 kW or 11 kW one to three-phase, with a current of up to 16 amps pro Phase. Whether with or without a solar system: The Kostal Wallbox is refueling your electric car from all available energy sources. Battery and fast charging, it depends on it and that is exactly one of the great strengths of the Kostal Wallbox. In conjunction with the Kostal Smart Energy meter, optional comfort functions are also available. In power mode, ENECTOR focuses on fast charging with the maximum available performance. Lock mode blocks the charging function from unwanted use. The two solar LADENODI "Solar Pure Mode" and "Solar Plus Mode" are particularly efficient in their effect. In the solar pure mode, the solar power produced is loaded exclusively. Only as much can be loaded here as is currently available. The charging capacity is adjusted for solar plus fashion to minimize the network performance cover. It can be taken into account whether the energy is used from a connected battery memory or not.
€696,00
-
Alfen Alfen base for Eve Double Pro-Line
The alfen stand is especially for the Alfen Eve Double Pro-Line Wallbox designed and offers an ideal solution for installing your outdoor charging station. Made made of robust stainless steel, this base guarantees high resistance to weather influences and durability. Characteristics: Material: Stainless steel Weight: Approx. 11 kg Color: Silver Dimensions: Length 1430 mm, width 180 mm, height 80 mm Foundation: Class B300 recommended (available separately) Advantages: Optimized for the outdoor area: Thanks to the resistant stainless steel, the base is ideal for using outdoor use. Stable installation: The recommended use of a B300 foundation ensures safe and stable attachment. Flexibility: Enables the installation of the Alfen Eve Double Pro-Line wall box outside of garages and other protected areas. Scope of delivery: 1x alfen stand for Eve Double Pro-Line About Alfen: Alfen is a leading Dutch company that specializes in the production of charging infrastructure for electric vehicles. The company attaches particular importance to reliability, sustainability and innovation, and offers solutions for both private and commercial applications.
€380,00
-
Growatt Growatt EV-Charger Thor 07AS-S-V1 (WiFi, RFID)
The intelligent AC charging station from the Thor series is an advanced energy supply that uses professional and highly developed technology to supply electric vehicles with energy. The Growatt Thor 07AS-S-V1 (WIFI, RFID) also has a user-friendly human-machine interface and offers versatile functions for control, billing and communication. Growatt Thor 07AS-S-V1 charging station This charging station can be seamlessly connected to a back office server, which enables functions such as reservation and payment via a mobile app. The Growatt charging station Thor 07AS-S-V1 is compatible with all brands of electric vehicles and can be integrated into existing and newly installed PV systems. In addition, the charging station makes it easier to charge electric vehicles with excess solar energy for 100 % renewable energy. Enjoy intelligent control and planning through the app. The IP65 design ensures the suitability for both indoor and outdoor use.
€589,00
-
Charge Amps Charge amps aura - 2 x 22 kW 3p 32a with Simcard
With the Solaredge Smart Energy socket, users transform their home into an intelligent energy management system in no time at all. The Smart Energy socket is a device that is used in conjunction with solaredge interim judges and intelligent energy management systems. It is designed to optimize energy consumption in a house or company with solar energy. How does the Solaredge Smart Energy socket work? The smart energy socket works like an intelligent socket and enables the user to connect and manage electrical devices. The device can control the energy flow of the solar energy system and prioritize the use of self -generated solar energy in order to supply connected devices with electricity. The solared monitoring software enables the user to control and monitor energy consumption in real time. For example, you can set schedules to determine when certain devices should be switched on or off in order to optimally use the available solar energy. This solaredge Smart Energy socket has been specially developed for France and Belgium. The Solaredge Smart Energy socket has wireless switches for electrical devices. The socket is supplied with an integrated energy knife and delivers energy measurements of up to 3 kWh. Maximum energy consumption: Can be remotely switched on or off according to a pre-integrated program or dynamically controlled by the inverter to maximize your own consumption.
€2.576,00
-
Alfen Alfen Eve single Pro-Line 3ph (RFID, 32A, T2, LBA, Logo, E-Flux)
The Alfen Eve Single Pro-Line 3ph EV charger is configured with the following functions in advance: RFID reader: Supports user identification for easy access. Load balancing Active: Automatically divides the available performance between the loading vehicles. The charger analyzes the available capacity and the performance requirements of the vehicle and then distributes the performance based on the maximum capacity of the connection. This ensures that electric vehicles can always be loaded, even with limited installation capacity, without having to carry out expensive upgrades. Back office integration with e-flux: Alfen charging stations can now be ordered with integration into the E-Flux Emobility platform. This enables plug & play installation and enables owners to manage charging tariffs and display meetings via the e-flux portal. E-Flux takes over the invoice and handling of charging sessions for connected alfine charging stations. Logodisplay: Contains the possibility of displaying a logo on the screen of the Alfen EV charging device and thus offers opportunities for branding. The Alfen Eve Single Pro-Line offers a compact solution for loading needs at home and in business. The user interacts via a 3.5-inch color monitor with a logo upload function that offers unique branding options. The charger offers user authentication options and plug-and-and-charge accessibility, whereby the usage data can be called up via any web-enabled device. About Alfen: Alfen is a leading Dutch company that specializes in the production of charging infrastructure for electric vehicles. The company attaches particular importance to reliability, sustainability and innovation, and offers solutions for both private and commercial applications.
€1.553,00
They have 65 from 65 Seen products